全国服务热线:15953195999
产品中心
您所在的位置:首页-新闻中心-常见问题叉车制动系统、转向系统故障处理办法

叉车制动系统、转向系统故障处理办法

来源:https://www.jnhgjx.net/ 日期:2022-07-07 发布人:

想要让叉车租赁过程减少工作失误,为重要的就是能够对叉车做好了解,能够熟知各项故障的原因和排除的办法,这对叉车维修来说有着更大的意义所在。下面来了解下叉车制动系统、转向系统故障处理办法吧。
If you want to reduce work errors in the forklift leasing process, it is important to understand the forklift well and be familiar with the causes of various faults and troubleshooting methods, which is of greater significance for forklift maintenance. Now let's learn about the troubleshooting of forklift braking system and steering system.
一、两轮不能同时制动,分析故障原因有:
1、 The two wheels cannot be braked at the same time. The causes of the failure are analyzed as follows:
1.两个制动器之间的间隙不同或制动器管道堵塞,调整两个制动器之间的间隙或疏通管道;
1. If the gap between the two brakes is different or the brake pipe is blocked, adjust the gap between the two brakes or dredge the pipe;
2.制动鼓内有油污或制动蹄扭曲变形,处理方法是清除油污或修理。更换制动蹄;
2. There is oil stain in the brake drum or the brake shoes are twisted and deformed. The treatment method is to remove the oil stain or repair. Replace the brake shoes;
3.制动管道内有空气,处理方法是排除制动管道内的空气。
3. There is air in the brake pipe. The treatment method is to eliminate the air in the brake pipe.
二、手制动失灵,这可能是由于手制动钢丝松弛,处理方法是调整手制动钢丝的紧度。
2、 The hand brake fails, which may be due to the relaxation of the hand brake steel wire. The treatment method is to adjust the tightness of the hand brake steel wire.
三、制动失灵,分析故障的原因有:
3、 Brake failure. The causes of the failure are analyzed as follows:
1.制动鼓与制动蹄间隙过大,处理方法是调制制动鼓与制动蹄间隙;
1. The clearance between brake drum and brake shoe is too large. The treatment method is to adjust the clearance between brake drum and brake shoe;
2.制动总泵进出液阀故障,处理方法是对进出液阀进行检修;
2. If the inlet and outlet valve of the brake master cylinder fails, the treatment method is to overhaul the inlet and outlet valve;
威尼斯官方网站登录
3.制动摩擦片磨损过大,处理方法是更好的摩擦片;
3. The brake friction plate is excessively worn, and the treatment method is better friction plate;
4.摩擦片接触面不够,处理方法是修理摩擦片。
4. The contact surface of the friction plate is not enough, and the treatment method is to repair the friction plate.
威尼斯官方网站登录总结了转向系统的常见故障和处理方法。
Jinan forklift leasing summarizes the common faults and handling methods of the steering system.
一、转向器漏油,分析故障原因有:
1、 The steering gear leaks oil, and the causes of the failure are analyzed as follows:
1.转向器各接头表面(阀体、隔板、定子、转子)漏油这种处理方法是更换密封圈,清洁转向器。接合面或更好的螺栓;
1. There is oil leakage on the joint surfaces of the steering gear (valve body, diaphragm, stator and rotor). This treatment method is to replace the sealing ring and clean the steering gear. Joint face or better bolt;
2.轴颈或溢流阀密封圈损坏,处理方法比较简单,即轴颈及溢流阀密封圈较好;
2. The shaft journal or overflow valve sealing ring is damaged, and the treatment method is relatively simple, that is, the shaft journal and overflow valve sealing ring are better;
3.限位螺栓处的垫圈不均匀。这种情况的处理方法是将垫圈磨平或更好的垫圈。
3. The washer at the limit bolt is uneven. The way to deal with this situation is to grind the washer flat or a better washer.
二、转向失灵,分析故障原因有:
2、 Steering failure. The causes of the failure are analyzed as follows:
1.转向器弹簧片断裂或转向器销轴断裂变形,也可能是联轴器开口断裂或变形处理方法是更好的弹簧片。销轴。联轴器;
1. The steering gear spring plate is broken or the steering gear pin shaft is broken and deformed, or the coupling opening is broken or deformed. The treatment method is a better spring plate. pin shaft. Coupling;
2.安全阀失灵,处理办法就是清洗安全阀、更换弹簧;
2. If the safety valve fails, the solution is to clean the safety valve and replace the spring;
3.转向缸泄漏过大,处理方法是更换密封件或缸。
3. If the leakage of steering cylinder is too large, the treatment method is to replace the seal or cylinder.
以上就是问题解答的相关内容了,希望能够帮助到大家,如对这一问题还存在任何疑问,都欢迎关注我们网站并咨询我们的工作人员,将竭诚为您服务。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website And consult our staff, will serve you wholeheartedly.

8040网站威尼斯
地址:山东省济南市章丘区龙山街道济青路龙山段南侧1幢   电话:15953195999
网站:https://www.jnhgjx.net/   备案号:鲁ICP备14018186号-1  

鲁公网安备 37011202000702号

 

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】

8040网站威尼斯_【唯一授权网站】