全国服务热线:15953195999
产品中心
您所在的位置:首页-新闻中心-常见问题8040网站威尼斯安全装置有哪些要求?

8040网站威尼斯安全装置有哪些要求?

来源:https://www.jnhgjx.net/ 日期:2019-11-26 发布人:

  门框不得变形或拆焊。内外门框之间的滚动间隙应合理调整,不得大于1.5mm。托辊的转动应灵活,托辊和轴应无裂纹和缺陷。砂轮槽的磨损量不得超过原尺寸的10%。

  The door frame shall not be deformed or disassembled for welding. The rolling clearance between the inner and outer door frames shall be adjusted reasonably and shall not be greater than 1.5mm. The rotation of idler shall be flexible, and the idler and shaft shall be free of cracks and defects. The wear of grinding wheel groove shall not exceed 10% of the original size.
  搁架和搁架必须完整、有效。
  Shelves and shelves must be complete and effective.
  3.两吊链张紧度均匀,不变形,端部连接牢固。链条的节距不应超过原来长度的4%,否则应更换链条。链轮转动应灵活。
  3. The tension of the two chains shall be uniform without deformation, and the ends shall be firmly connected. The pitch of the chain shall not exceed 4% of the original length, otherwise the chain shall be replaced. The sprocket shall rotate flexibly.
  4. 货物叉架不得有严重变形或脱焊。货叉表面不得有裂纹或焊接。货物叉角不得大于93°,厚度不得小于原尺寸的90%。左右叉点高度差不得超过叉水平长度的3%。货叉的定位要可靠,货叉钩的支撑面和定位面不应有明显的缺陷,货叉与货叉架的配合间隙不宜过大,动作要平稳。
  4. There shall be no serious deformation or desoldering of cargo fork frame. There shall be no cracks or welding on the fork surface. The cargo fork angle shall not be more than 93 ° and the thickness shall not be less than 90% of the original size. The height difference between the left and right fork points shall not exceed 3% of the fork horizontal length. The positioning of the fork shall be reliable, the supporting surface and positioning surface of the fork hook shall be free of obvious defects, the fitting clearance between the fork and the fork frame shall not be too large, and the action shall be stable.
济南8040网站威尼斯
  5. 升降缸与门框的连接应牢固灵活,配合间隙不宜过大。钢瓶密封良好,无裂纹,工作平稳。在额定载荷下,lOmin龙门架自沉能力不得超过20mm,倾角不得超过0。5°。满载时的起升速度不应小于标准值的一半。
  5. The connection between lifting cylinder and door frame shall be firm and flexible, and the fitting clearance shall not be too large. The cylinder is well sealed, free of cracks and stable. Under the rated load, the self sinking capacity of the LOMIN gantry shall not exceed 20 mm, and the inclination angle shall not exceed 0. 5 degrees. The lifting speed under full load shall not be less than half of the standard value.
  7. 严禁站在货叉的顶部和底部。不允许使用一个单独的货叉来挑高于负载的货物。
  7. It is forbidden to stand on the top and bottom of the fork. It is not allowed to use a single fork to pick goods higher than the load.
  6. 应配备有叉车驾驶证的叉车司机,以避免一辆叉车内多名司机。
  6. Forklift drivers with forklift driver license shall be equipped to avoid multiple drivers in a forklift.

8040网站威尼斯
地址:山东省济南市章丘区龙山街道济青路龙山段南侧1幢   电话:15953195999
网站:https://www.jnhgjx.net/   备案号:鲁ICP备14018186号-1  

鲁公网安备 37011202000702号

 

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】

8040网站威尼斯_【唯一授权网站】